Anritsu MT8221B BTS Master Base Station Cable Antenna Spectrum Analyzer 7.1 GHz

$2699.0 Buy It Now or Best Offer
free,30-Day Returns

Seller Store abtech_global
(4543) 100.0%,

Location: Southgate, Michigan
Ships to: US,
Item: 356093610541

Restocking Fee:No
Return shipping will be paid by:Buyer
All returns accepted:Returns Accepted
Item must be returned within:30 Days
Refund will be given as:Money back or replacement (buyer’s choice)
Anritsu:Anritsu
MPN:Does not apply
MT8221B:MT8221B
Frequency Range:400 MHz to 4 GHz / 150 kHz to 7.1 GHz
Installed Options:10, 25, 27, 31, 33, 34, 42, 43, 62, 63, 541, 542, 546

The Following Items Are Included: Anritsu MT8221B BTS Master Base Station Analyzer (BC# 44377-L/T*) Installed Options: Option 10: Bias Tee Option 25: Interference Analyzer Option 27: Channel Scanner Option 31: GPS Receiver Option 33: cdmaOne/CDMA2000 1X Over-The-Air Measurements Option 34: CDMA2000 1xEV-DO Over-The-Air Measurements Option 42: cdmaOne/CDMA2000 1X RF Measurements Option 43: cdmaOne/CDMA2000 1X Demodulation Option 62: CDMA2000 1xEV-DO RF Measurements Option 63: CDMA2000 1xEV-DO Demodulation Option 541: LTE RF Measurements (BW – < 10 MHz) Option 542: LTE Modulation Measurements (BW - < 10 MHz) Option 546: LTE Over-The-Air Measurements (2) BNC Cables USB PC Interface Cable DC Car Charger AC Adapter/Charger Power Cord USB PC Interface Cable User Manual On CD-ROM Carrying Case (G) BE SURE TO CHECK OUR EBAY STORE FOR OTHER ITEMS! This Item Has A Current Calibration! Anritsu MT8221B BTS Master Base Station AnalyzerCable and Antenna Frequency Range: 400 MHz to 4 GHzSpectrum Analyzer Frequency Range: 150 kHz to 7.1 GHzInstalled Options:- Option 10: Bias Tee- Option 25: Interference Analyzer - Option 27: Channel Scanner - Option 31: GPS Receiver - Option 33: cdmaOne/CDMA2000 1X Over-The-Air Measurements - Option 34: CDMA2000 1xEV-DO Over-The-Air Measurements - Option 42: cdmaOne/CDMA2000 1X RF Measurements - Option 43: cdmaOne/CDMA2000 1X Demodulation - Option 62: CDMA2000 1xEV-DO RF Measurements - Option 63: CDMA2000 1xEV-DO Demodulation - Option 541: LTE RF Measurements (BW - < 10 MHz)- Option 542: LTE Modulation Measurements (BW - < 10 MHz)- Option 546: LTE Over-The-Air MeasurementsIncludes Carrying Case & Accessories As Listed Above! Working Condition: ExcellentCondition: RefurbishedCalibrated: Yes Warranty: 1 YEAR WARRANTY Anritsu MT8221B BTS Master Base Station AnalyzerThe BTS Master MT8221B and MT8222B are high-performance handheld base station analyzers that have been specifically developed to support the emerging 4G standards as well as installed 2G, 3G and WiMAX networks. The MT822xB platform introduces: 20 MHz LTE modulation quality testing Vector Signal Generator (400 MHz to 6 GHz) for comprehensive receiver testing 30-MHz Zero-Span IF Output for external demodulation of virtually any other wideband signal The BTS Master features over 30 analyzers in one to meet virtually every measurement need. Standard features are: 2-port Cable and Antenna Analyzer: 400 MHz to 4 GHz Spectrum Analyzer: 150 kHz to 7.1 GHz Power Meter: 10 MHz to 7.1 GHz Meeting Key Performance Indicators (KPIs)Degradation in KPIs, such as dropped call and/or blocked call rates due to a malfunction at the cell site or due to interference, can be easily and accurately diagnosed down to the base station field replaceable unit (FRU) or the offending interfering signal with the BTS Master.Line Sweep Tools (LST)LST is a PC program that post processes Antenna, Cable, and PIM traces. It provides a powerful trace analysis and report generator for line sweepers.Master Software Tools (MST)MST is a PC program that post processes spectrum analysis traces collected on your instrument. It provides a powerful data analysis tools for spectrum clearing and interference monitoring. With Anritsu’s design know-how and demanding production testing and performance verification you can count on the BTS Master to give you years of reliable dependable service.Cable and Antenna Analyzer The BTS Master features 1-port and 2-port Cable and Antenna Analyzer and a PIM Analyzer to be able to test and verify the performance of nearly every feed-line and antenna component. This includes: Connectors Cables/Jumpers Antenna Isolation Diplexers/Duplexers Tower Mounted Amplifiers The goal of these measurements is to maximize the coverage, data rate and capacity with problem-free antenna systems minimizing dropped calls and blocked calls for a good customer experience.Antenna Systems Failure MechanismsMaintenance is an on-going requirement as antenna systems’ performance can degrade at any point in time due to: Loose connectors Improperly weatherized connectors Pinched cables Poor grounding Corroded connectors Lightning strikes Strong winds misaligning antennas Rain getting into cables Bullet holes/nails in the cable Intermodulation of multiple signals Making Measurements EasierThe BTS Master provides features for making measurements easier to perform and to analyze test results such as: FlexCal eliminates the need to recalibrate when changing frequencies High RF Immunity for testing in harsh RF environments Trace OVerlay compares reference traces to see changes over time Limit Lines and Alarming for providing reference standards High Power output to test tower-top components without climbing the tower Internal Bias-Tee to power up TMAs for testing when off-line GPS tagging of data to verify location of tests Line Sweep Tools for post-analysis and report generation Spectrum AnalyzerThe BTS Master features the most powerful handheld spectrum analyzer for field use with unmatched performance such as: Sensitivity Dynamic Range Phase Noise Frequency Accuracy Resolution Bandwidth (RBW) The goal of the Spectrum Analyzer’s measurements is to be able to monitor, measure, and analyze RF signals and their environments. It finds rogue signals, measures carriers and distortion, and verifies base stations’ signal performance. It validates carrier frequency and identifies desired and undesired signals.Simple But Powerful The BTS Master features dedicated routines for one-button measurements and for more in-depth analysis the technician has control over the setting and features not even found on lab-grade benchtop spectrum analyzers, for instance: Multiple sweep detection methods - true RMS detector, quasipeak, ... Multiple traces and control - three traces, trace math, ... Advanced marker function - noise marker, frequency counter, ... Advanced limit line functions - one-button envelope creation, relative, ... Save-on-Event - auotmatically saves a sweep when crossing a limit line Gated sweep - view pulsed or burst signals only when they are on, or off I/Q waveform capture - transfer captured signals for further analysis and troubleshooting Power MetersThe BTS Master offers as standard a builtin Power Meter utilizing the Spectrum Analyzer and an optional High Accuracy Power Meter requiring external power sensors.Setting the transmitter output power of a base station properly is critical to the overall operation of a wireless network. A 1.5 dB change in power levels means a 15% change in coverage area.Too much power means overlapping coverage which translates into cell-tocell self interference. Too little power, too little coverage, creates island cells with non-overlapping cell sites and reduced in-building coverage. High or low values will cause dead zones/dropped calls, lower data rates/reduced capacity near cell edges, and cell loading imbalances/blocked calls.Specifications: Cable and Antenna Analyzer Measurements VSWR, Return Loss, Cable Loss, Distance-to-Fault (DTF) VSWR, Distance-to-Fault (DTF) Return Loss, 1-port Phase, 2-port Phase, 2-port Gain, Smith Chart Setup Parameters Frequency Start/Stop, Signal Standard, Start Cal DTF Start/Stop, DTF Aid, Units (m/ft), Cable Loss, Propagation Velocity, Cable, Windowing Windowing Rectangular, Normal Side Lobe, Low Side Lobe, Minimum Side Lobe Amplitude Top, Bottom Auto Scale, Full Scale Sweep Run/Hold, Single/Continuous, RF Immunity (High/Low), Data Points, Averaging/Smoothing, Output Power (High/Low) Data Points 137, 275, 551 Markers Markers 1 to 6 each with a Delta Marker, Marker to Peak/Valley, Marker Table (On/Off), All Markers Off Traces Recall, Copy to Display Memory, No Trace Math, Trace + Memory, Trace - Memory, Trace Overlay (On/Off) Limit Line On/Off, Single Limit, Multi-segment (41), Limit Alarm, Clear Limit Line Edit Frequency, Amplitude, Add Point, Delete Point, Next Point Left, Next Point Right, Move Limit Calibration Start Cal, 1/2-port, Low/High Power, Standard/FlexCal™, DUT Connector, Configure DUT Save/Recall Setups, Measurements, Screen Shots (JPEG - save only) Application Options Bias-Tee (On/Off) Frequency Frequency Range 400 MHz to 4 GHz Frequency Accuracy ± 3.0 ppm Frequency Resolution 1 kHz (RF immunity low) 100 kHz (RF immunity high) Output Power High –7 dBm, typical, 1 or 2-port Low –40 dBm, typical, 2-port Dynamic Range 400 MHz to 3.0 GHz 80 dB > 3.0 GHz to 4.0 GHz 70 dB Interference Immunity On-Channel +17 dBm @ >1.0 MHz from carrier frequency On-Frequency +10 dBm within ±10 kHz from the carrier frequency Measurement Speed Return Loss ≤ 4.5 ms/data point, RF immunity low, typical Distance-To-Fault ≤ 4.5 ms/data point, RF immunity low, typical Return Loss Measurement Range 0 to 60 dB Resolution 0.01 dB VSWR Measurement Range 1:1 to 65:1 Resolution 0.01 Cable Loss Measurement range 0 to 30 dB Resolution 0.01 dB 2-Port Gain Measurement range -120 to +100 dB Resolution 0.01 dB Distance-to-Fault Vertical Range Return Loss 0 dB to 60 dB Vertical Range VSWR 1 to 65 Fault Resolution (m) (1.5 x 108 x vp) / ∆F (vp = velocity propagation constant, ∆F is F2-F1 in Hz) Horizontal Range (m) 0 to (Data Points-1) x Fault Resolution, to a maximum of 1500 m (4921 ft) Phase (1- and 2-Port) Measurement Range –180° to +180° Resolution 0.01° Smith Chart Resolution 0.01 Measurement Accuracy Corrected Directivity > 42 dB Spectrum Analyzer Measurements Smart Measurements Field Strength (dBm/m2, dBW/m2, V/m, A/m, Watt/m2, Watt/cm2, or dBmV/m) Occupied Bandwidth (measures 99 % to 1 % power channel of a signal) Channel Power (measures the total power in a specified bandwidth) ACPR (adjacent channel power ratio) AM/FM/SSB Demodulation (wide/narrow FM, upper/lower SSB), (audio out only) C/I (carrier-to-interference ratio) Emission Mask (recall limit lines as emission mask) Setup Parameters Frequency Center/Start/Stop, Span, Frequency Step, Frequency Offset, Signal Standard, Channel # Amplitude Reference Level (RL), Scale, Attenuation Auto/Level, RL Offset, Pre-Amp On/Off, Detection Span Span, Span Up/Down (1-2-5), Full Span, Zero Span, Last Span Bandwidth RBW, Auto RBW, VBW, Auto VBW, RBW/WBW, Span/RBW Application Options Bias-Tee (On/Off), Impedance (50 Ω, 75 Ω, Other) Sweep Functions Sweep Single/Continuous, Manual Trigger, Reset, Detection, Minimum Sweep Time, Trigger Type Detection Peak, RMS, Negative, Sample, Quasi-peak Triggers Free Run, External, Video, Change Position, Manual Trace Functions Traces Up to three Traces (A, B, C), View/Blank, Write/Hold, Trace A/B/C Operations Trace A Operations Normal, Max Hold, Min Hold, Average, # of Averages, (always the live trace) Trace B Operations A → B, B ←→ C, Max Hold, Min Hold Trace C Operations A → C, B ←→ C, Max Hold, Min Hold, A – B → C, B – A → C, Relative Reference (dB), Scale Marker Functions Markers Markers 1–6 each with a Delta Marker, or Marker 1 Reference with Six Delta Markers, Marker Table (On/Off/Large), All Markers Off Marker Types Style (Fixed/Tracking), Noise Marker, Frequency Counter Marker Marker Auto-Position Peak Search, Next Peak (Right/Left), Peak Threshold %, Set Marker to Channel, Marker Frequency to Center, Delta Marker to Span, Marker to Reference Level Marker Table 1–6 markers frequency and amplitude plus delta markers frequency offset and amplitude Limit Line Functions Limit Lines Upper/Lower, On/Off, Edit, Move, Envelope, Advanced, Limit Alarm, Default Limit Limit Line Edit Frequency, Amplitude, Add Point, Add Vertical, Delete Point, Next Point Left/Right Limit Line Move To Current Center Frequency, By dB or Hz, To Marker 1, Offset from Marker 1 Limit Line Envelope Create Envelope, Update Amplitude, Number of Points (41), Offset, Shape Square/Slope Limit Line Advanced Type (Absolute/Relative), Mirror, Save/Recall Frequency Frequency Range 150 kHz to 7.1 GHz (usable to 0 Hz) Maximum Continous Input +30 dBm Tuning Resolution 1 Hz Frequency Reference Aging: ± 1.0 ppm/10 years Frequency Span Accuracy: ± 0.3 ppm (25 °C ± 25 °C) + aging 10 Hz to 7.1 GHz including zero span Sweep Time Minimum 100 ms, 10 μs to 600 s in zero span Sweep Time Accuracy ± 2 % in zero span Bandwidth Resolution Bandwidth (RBW) 1 Hz to 3 MHz in 1–3 sequence ±10 % (1 MHz max in zero-span) (–3 dB bandwidth) Video Bandwidth (VBW) 1 Hz to 3 MHz in 1–3 sequence (–3 dB bandwidth) RBW with Quasi-Peak Detection 200 Hz, 9 kHz, 120 kHz (–6 dB bandwidth) VBW with Quasi-Peak Detection Auto VBW is On, RBW/VBW = 1 VBW/Average Type Linear/Log Spectral Purity SSB Phase Noise –100 dBc/Hz @ 10 kHz, 20 kHz and 30 kHz offset from carrier–102 dBc/Hz @ 100 kHz offset from carrier Amplitude Ranges Dynamic Range > 95 dB (600 MHz, 3.5 GHz), 2/3 (TOI-DANL) in 1 Hz RBW Measurement Range DANL to +30 dBm Display Range 1 dB to 15 dB/div in 1 dB steps, ten divisions displayed Reference Level Range –120 dBm to +30 dBm Attenuator Resolution 0 dB to 65 dB, 5.0 dB steps Amplitude Units Log Scale Modes: dBm, dBV, dBmv, dBμV, dBW, dBA Linear Scale Modes: nV, μV, mV, V, kV, nW, μW, mW, W, kW, fA, pA, nA, μA, mA, A Amplitude Accuracy (Power level > –50 dBm) Input attenuation Preamp Off (≤ 35 dB) Preamp Off (40 to 55 dB) Preamp Off (60 to 65 dB) Preamp On (0 or 10 dB) 150 kHz to ≤10 MHz ± 1.50 dB ± 1.50 dB ± 1.50 dB – 150 kHz to 4.0 GHz – – – ± 1.50 dB >10 MHz to 4.0 GHz ± 1.25 dB ± 1.75 dB ± 1.75 dB – >4.0 GHz to 6.5 GHz – ± 1.75 dB ± 1.75 dB – >4.0 GHz to 7.1 GHz ± 1.75 dB – – ± 1.75 dB >6.5 GHz to 7.1 GHz – ± 2.00 dB ± 3.00 dB – Displayed Average Noise Level (DANL) Preamp Off (Reference level –20 dBm) Preamp On (Reference level –50 dBm) DANL in 1 Hz RBW, 0 dB attenuation Maximum Typical Maximum Typical 3 MHz to 1.0 GHz –137 dBm –150 dBm –161 dBm –163 dBm > 1.0 GHz to 2.2 GHz –133 dBm –147 dBm –159 dBm –160 dBm > 2.2 GHz to 4.0 GHz –133 dBm –143 dBm –156 dBm –159 dBm > 4.0 GHz to 7.1 GHz –130 dBm –138 dBm –154 dBm –156 dBm Spurs Residual Spurs Preamp Off (RF input terminated, 0 dB input attenuation) –90 dBm, 150 kHz to 3.2 GHz –84 dBm, > 3.2 GHz to 7.1 GHz Exceptions –70 dBm @ 3200 MHz Preamp On (RF input terminated, 0 dB input attenuation) –100 dBm. 10 MHz to 7.1 GHz Exceptions –95 dBm @ 50, 100, 150 MHz Input-Related Spurious (0 dB attenuation, –30 dBm input, span <1.7 GHz, carrier offset > 4.5 MHz) –60 dBc, –70 dBc typical Exceptions –40 dBc, –60 dBc typical @ 1672 MHz Third-Order Intercept (TOI) Preamp Off 600 MHz +8 dBm typical Preamp Off 3.5 GHz +9 dBm typical Second Harmonic Distortion Preamp Off –50 dBc maximum –70 dBc typical VSWR <4.0 GHz 1:5:1 typical 4.0 GHz to 7.1 GHz 1.8:1 typical Power Meter General Frequency Center/Start/Stop, Span, Frequency Step, Signal Standard, Channel #, Full Band Amplitude Maximum, Minimum, Offset, Relative On/Off, Units, Auto Scale Average Acquisition Fast/Med/Slow, # of Running Averages Limits Limit On/Off, Limit Upper/Lower Frequency Range 10 MHz to 7.1 GHz Span 1 kHz to 100 MHz Display Range –140 dBm to +30 dBm, ≤ 40 dB span Measurement Range –120 dBm to +30 dBm Offset Range 0 to +100 dB VSWR 1.5:1 typical Maximum Power +30 dBm without attenuator Accuracy Same as Spectrum Analyzer Application Options Impedance (50 Ω, 75 Ω, Other) Please check our Huge Inventory with savings of up to 80% off of retail on Cat5/5e/6 LAN Cable Certifiers and Fiber Optic OTDR's, Fusion Splicers, CATV Meters, Fiber Optic Kits, Sources, Meters, Tools, Network Analyzers and much more. Here is a Link to our Ebay Test Equipment Store. All of our Test Equipment is backed with a Full Warranty and unbeatable customer support & service. Please don't hesitate to contact us for a Quote on Something you don't see in our inventory, sometimes we have items that may have not been listed or processed yet. Test Equipment Store Offers a wide range of Refurbished Telecom/ Datacom Tools and Test Measurement Equipment. Which includes Fiber Optic Test and Splicing tools, Fusion Splicers, OTDRs, Copper and Fiber Cable Certifiers, CATV Test Equipment, Cable and Antenna Analyzers, Network Analyzers and much more! We carry a large inventory of quality refurbished and used test equipment from all the major manufacturers. If you are looking for multiple quantities or if we don't have a listing for a particular item that you are looking for. Please contact us as it may be fresh inventory waiting to be listed or we'll be glad to find it for you at the best price possible and put up an eBay listing for you! We Ship World Wide! We will attempt to ship your item(s) within 24 hours after payment has been received. To get a real-time shipping quote to your destination, enter your country and zip / postal code information into the shipping calculator and click "Get Rate".Many countries impose their own customs, duties, tariffs, taxes, etc. on items being shipped from a foreign country. We do not cover those cost's and we recommend that you contact your countries customs agency for that information.We Offer Multiple Quantity Price & Shipping Discounts, Email Us If You Are Interested In Larger Quantities. We accept credit card payment transactions via the online checkout system! The checkout process is designed so that it communicates with the merchant to confirm that payment has been made and cleared. Other methods of payment are outlined through the online checkout process. Winning bidders must contact us within 3 days after auction close if special payment arrangements are needed. Your payment is expected within 5 days after the auction close. Unpaid auctions will be forfeited after 5 days of the auction close and the Item(s) will be relisted for sale. Items will be shipped within 24 hours (1 Business Day) upon receipt of payment from the winning bidder. (Certain orders may take longer for processing due to comprehensive final service inspections) A Shipment Tracking number(s) will be provided to inform Buyers of their expected ETA (Estimated Time of Arrival). Tracking number(s) will be provided the same day as order shipment. Thank you ALL MAJOR CREDIT CARDS & PayPal ACCEPTED Sell Smarter with Kyozou.Inventory and Ecommerce Management

Frequently Asked Questions About Anritsu MT8221B BTS Master Base Station Cable Antenna Spectrum Analyzer 7.1 GHz in My Website

funupacademy.com is the best online shopping platform where you can buy Anritsu MT8221B BTS Master Base Station Cable Antenna Spectrum Analyzer 7.1 GHz from renowned brand(s). funupacademy.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling Anritsu MT8221B BTS Master Base Station Cable Antenna Spectrum Analyzer 7.1 GHz on funupacademy.com?